ATtiny48 datasheet(91/266 Pages) ATMEL

91 / 266 page

8008C–AVR–03/09

ATtiny48/88

Reading the 16-bit value in the Input Capture Register (ICR1) is done by first reading the low

byte (ICR1L) and then the high byte (ICR1H). When the low byte is read the high byte is copied

into the high byte temporary register (TEMP). When the CPU reads the ICR1H I/O location it will

access the TEMP Register.

The ICR1 Register can only be written when using a Waveform Generation mode that utilizes

the ICR1 Register for defining the counter’s TOP value. In these cases the Waveform Genera-

tion mode (WGM13:0) bits must be set before the TOP value can be written to the ICR1

before the low byte is written to ICR1L.

For more information on how to access the 16-bit registers refer to “Accessing 16-bit Registers”

on page 86.

12.6.1

Input Capture Trigger Source

The main trigger source for the Input Capture unit is the Input Capture pin (ICP1).

Timer/Counter1 can alternatively use the Analog Comparator output as trigger source for the

Input Capture unit. The Analog Comparator is selected as trigger source by setting the Analog

Comparator Input Capture (ACIC) bit in the Analog Comparator Control and Status Register

(ACSR). Be aware that changing trigger source can trigger a capture. The Input Capture Flag

must therefore be cleared after the change.

Both the Input Capture pin (ICP1) and the Analog Comparator output (ACO) inputs are sampled

using the same technique as for the T1 pin (Figure 13-1 on page 112). The edge detector is also

identical. However, when the noise canceler is enabled, additional logic is inserted before the

edge detector, which increases the delay by four system clock cycles. Note that the input of the

noise canceler and edge detector is always enabled unless the Timer/Counter is set in a Wave-

form Generation mode that uses ICR1 to define TOP.

An Input Capture can be triggered by software by controlling the port of the ICP1 pin.

12.6.2

Noise Canceler

The noise canceler improves noise immunity by using a simple digital filtering scheme. The

noise canceler input is monitored over four samples, and all four must be equal for changing the

output that in turn is used by the edge detector.

The noise canceler is enabled by setting the Input Capture Noise Canceler (ICNC1) bit in

Timer/Counter Control Register B (TCCR1B). When enabled the noise canceler introduces addi-

tional four system clock cycles of delay from a change applied to the input, to the update of the

ICR1 Register. The noise canceler uses the system clock and is therefore not affected by the

prescaler.

12.6.3

Using the Input Capture Unit

The main challenge when using the Input Capture unit is to assign enough processor capacity

for handling the incoming events. The time between two events is critical. If the processor has

not read the captured value in the ICR1 Register before the next event occurs, the ICR1 will be

overwritten with a new value. In this case the result of the capture will be incorrect.

When using the Input Capture interrupt, the ICR1 Register should be read as early in the inter-

rupt handler routine as possible. Even though the Input Capture interrupt has relatively high

priority, the maximum interrupt response time is dependent on the maximum number of clock

cycles it takes to handle any of the other interrupt requests.

ATtiny48 Datasheet(PDF) 91 Page - ATMEL Corporation

ATtiny48 Datasheet(HTML) 91 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL