| Electronic Components Datasheet Search |
|
LP8556 Datasheet(PDF) 8 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
LP8556 Datasheet(HTML) 8 Page - Texas Instruments |
|
8 / 52 page ![]() LP8556 SNVS871B – JULY 2012 – REVISED SEPTEMBER 2012 www.ti.com Boost Converter Electrical Characteristics (1) (continued) Symbol Parameter Condition Min Typ Max Units tSTARTUP Startup time See(3) 8 ms IBOOST_LIM = 00 0.66 0.9 1.16 IBOOST_LIM_2X = IBOOST_LIM = 01 0.88 1.2 1.40 A 0 IBOOST_LIM = 10 1.12 1.5 1.73 IBOOST_LIM = 11 1.35 1.8 2.07 ISW_LIM SW pin current limit(4) IBOOST_LIM_2X = IBOOST_LIM = 00 1.6 1 IBOOST_LIM = 01 2.1 A IBOOST_LIM = 10 2.6 EN_DRV3 = 0 AND EN_DRV2 = 0 3.7 ΔVSW / SW pin slew rate during OFF EN_DRV3 = 0 AND EN_DRV2 = 1 5.3 V / ns toff_on to ON transition EN_DRV3 = 1 AND EN_DRV2 = 1 7.5 EN_DRV3 = 0 AND EN_DRV2 = 0 1.9 ΔVSW / SW pin slew rate during ON EN_DRV3 = 0 AND EN_DRV2 = 1 4.4 V / ns ton_off to OFF transition EN_DRV3 = 1 AND EN_DRV2 = 1 4.8 Peak to peak switch ON time ΔtON / tSW deviation to SW period ratio SSCLK_EN = 1 1 % (Spread spectrum feature) (3) Startup time is measured from the moment boost is activated until the VBOOST crosses 90% of its target value. (4) 1.8A is the maximum ISW_LIM supported with the DSBGA package. For applications requiring the ISW_LIM to be greater than 1.8A and up to 2.6A, WQFN package should be considered. LED Driver Electrical Characteristics (1) Symbol Parameter Condition Min Typ Max Units ILED_LEAKAGE Leakage current Outputs LED1...LED6, VOUT = 48V 0.1 1 μA Maximum Sink Current ILED_MAX 50 mA LED1...LED6 -3 1 +3 ILED LED Current Accuracy(2) Output current set to 23 mA % -4 +4 IMATCH Matching Output current set to 23 mA 0.5 % 100 Hz < fPWM ≤ 200 Hz 0.02 100 200 Hz < fPWM ≤ 500 Hz 0.02 100 500 Hz < fPWM ≤ 1 kHz 0.02 100 1 kHz < fPWM ≤ 2 kHz 0.04 100 LED PWM output pulse duty PWMDUTY 2 kHz < fPWM ≤ 5 kHz 0.1 100 % cycle(3) 5 kHz < fPWM ≤ 10 kHz 0.2 100 10 kHz < fPWM ≤ 20 kHz 0.4 100 20 kHz < fPWM ≤ 30 kHz 0.6 100 30 kHz < fPWM ≤ 39 kHz 0.8 100 fLED PWM output frequency PWM_FREQ = 1111 38.5 kHz VSAT Saturation Voltage(4) Output current set to 23 mA 200 mV (1) Min and Max limits are guaranteed by design, test, or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm. (2) Output Current Accuracy is the difference between the actual value of the output current and programmed value of this current. Matching is the maximum difference from the average. For the constant current sinks on the part (OUT1 to OUT6), the following are determined: the maximum output current (MAX), the minimum output current (MIN), and the average output current of all outputs (AVG). Two matching numbers are calculated: (MAX-AVG)/AVG and (AVG-MIN/AVG). The largest number of the two (worst case) is considered the matching figure. The typical specification provided is the most likely norm of the matching figure for all parts. Note that some manufacturers have different definitions in use. (3) Guaranteed by design and not tested in production. (4) Saturation voltage is defined as the voltage when the LED current has dropped 10% from the value measured at 1V. 8 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Links: LP8556 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |