ATtiny48 datasheet(146/266 Pages) ATMEL

146 / 266 page

146

8008C–AVR–03/09

ATtiny48/88

To initiate the Slave Transmitter mode, TWAR and TWCR must be initialized as follows:

The upper seven bits are the address to which the 2-wire Serial Interface will respond when

addressed by a Master. If the LSB is set, the TWI will respond to the general call address (0x00),

otherwise it will ignore the general call address.

TWEN must be written to one to enable the TWI. The TWEA bit must be written to one to enable

the acknowledgement of the device’s own slave address or the general call address. TWSTA

and TWSTO must be written to zero.

When TWAR and TWCR have been initialized, the TWI waits until it is addressed by its own

slave address (or the general call address if enabled) followed by the data direction bit. If the

direction bit is “1” (read), the TWI will operate in ST mode, otherwise SR mode is entered. After

its own slave address and the write bit have been received, the TWINT Flag is set and a valid

status code can be read from TWSR. The status code is used to determine the appropriate soft-

ware action. The appropriate action to be taken for each status code is detailed in Table 15-5.

The Slave Transmitter mode may also be entered if arbitration is lost while the TWI is in the

Master mode (see state 0xB0).

If the TWEA bit is written to zero during a transfer, the TWI will transmit the last byte of the trans-

fer. State 0xC0 or state 0xC8 will be entered, depending on whether the Master Receiver

transmits a NACK or ACK after the final byte. The TWI is switched to the not addressed Slave

mode, and will ignore the Master if it continues the transfer. Thus the Master Receiver receives

all “1” as serial data. State 0xC8 is entered if the Master demands additional data bytes (by

transmitting ACK), even though the Slave has transmitted the last byte (TWEA zero and expect-

ing NACK from the Master).

While TWEA is zero, the TWI does not respond to its own slave address. However, the 2-wire

Serial Bus is still monitored and address recognition may resume at any time by setting TWEA.

This implies that the TWEA bit may be used to temporarily isolate the TWI from the 2-wire Serial

Bus.

In all sleep modes other than Idle mode, the clock system to the TWI is turned off. If the TWEA

bit is set, the interface can still acknowledge its own slave address or the general call address by

using the 2-wire Serial Bus clock as a clock source. The part will then wake up from sleep and

the TWI will hold the SCL clock will low during the wake up and until the TWINT Flag is cleared

(by writing it to one). Further data transmission will be carried out as normal, with the AVR clocks

running as normal. Observe that if the AVR is set up with a long start-up time, the SCL line may

be held low for a long time, blocking other data transmissions.

Note that the 2-wire Serial Interface Data Register – TWDR does not reflect the last byte present

on the bus when waking up from these sleep modes.

TWAR

TWA6

TWA5

TWA4

TWA3

TWA2

TWA1

TWA0

TWGCE

value

Device’s Own Slave Address

TWCR

TWINT

TWEA

TWSTA

TWSTO

TWWC

TWEN

–

TWIE

value

100

ATtiny48 Datasheet(PDF) 146 Page - ATMEL Corporation

ATtiny48 Datasheet(HTML) 146 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL