ATtiny48 datasheet(151/266 Pages) ATMEL

151 / 266 page

151

8008C–AVR–03/09

ATtiny48/88

15.9

15.9.1

TWBR – TWI Bit Rate Register

• Bits 7..0 – TWI Bit Rate Register

TWBR selects the division factor for the bit rate generator. The bit rate generator is a frequency

divider which generates the SCL clock frequency in the Master modes. See “Bit Rate Generator

Unit” on page 130 for calculating bit rates.

If the TWI operates in Master mode TWBR must be set to 10, or higher.

15.9.2

TWCR – TWI Control Register

The TWCR is used to control the operation of the TWI. It is used to enable the TWI, to initiate a

Master access by applying a START condition to the bus, to generate a Receiver acknowledge,

to generate a stop condition, and to control halting of the bus while the data to be written to the

bus are written to the TWDR. It also indicates a write collision if data is attempted written to

TWDR while the register is inaccessible.

• Bit 7 – TWINT: TWI Interrupt Flag

This bit is set by hardware when the TWI has finished its current job and expects application

software response. If the I-bit in SREG and TWIE in TWCR are set, the MCU will jump to the

TWI Interrupt Vector. While the TWINT Flag is set, the SCL low period is stretched. The TWINT

Flag must be cleared by software by writing a logic one to it. Note that this flag is not automati-

cally cleared by hardware when executing the interrupt routine. Also note that clearing this flag

starts the operation of the TWI, so all accesses to the TWI Address Register (TWAR), TWI Sta-

tus Register (TWSR), and TWI Data Register (TWDR) must be complete before clearing this

flag.

• Bit 6 – TWEA: TWI Enable Acknowledge Bit

The TWEA bit controls the generation of the acknowledge pulse. If the TWEA bit is written to

one, the ACK pulse is generated on the TWI bus if the following conditions are met:

The device’s own slave address has been received.

A general call has been received, while the TWGCE bit in the TWAR is set.

A data byte has been received in Master Receiver or Slave Receiver mode.

By writing the TWEA bit to zero, the device can be virtually disconnected from the 2-wire Serial

Bus temporarily. Address recognition can then be resumed by writing the TWEA bit to one

again.

Bit

654

TWBR7

TWBR6

TWBR5

TWBR4

TWBR3

TWBR2

TWBR1

TWBR0

TWBR

Read/Write

R/W

Initial Value

Bit

654

TWINT

TWEA

TWSTA

TWSTO

TWWC

TWEN

–

TWIE

TWCR

Read/Write

R/W

Initial Value

ATtiny48 Datasheet(PDF) 151 Page - ATMEL Corporation

ATtiny48 Datasheet(HTML) 151 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL