AM8530 datasheet(120/194 Pages) AMD

120 / 194 page

AMD

6–10

6.2.4

Write Register 3 (Receive Parameters and Control)

This register contains the control bits and parameters for the receiver logic as illustrated

in Figure 6–4. This register is readable by executing a Read to RR9 when D0 of WR15

and D6 of WR7’ are set to ‘1’.

Bits 7 and 6: Receiver Bits/Character

The state of these two bits determines the number of bits to be assembled as a character

in the received serial data stream. Table 6–2 lists the number of bits per character in the

assembled character format. The number of bits per character can be changed while a

character is being assembled, but only before the number of bits currently programmed is

reached. Unused bits in the Received Data Register (RR8) are set to ‘1’ in asynchronous

modes. In synchronous modes and SDLC modes, the SCC transfers an 8-bit section of

the serial data stream to the receive FIFO at the appropriate time.

Table 6–2. Receive Bits/Character

Character Length

5 Bits/Character

7 Bits/Character

6 Bits/Character

8 Bits/Character

Bit 5: Auto Enables

This bit programs the function for both

DCD and CTS pins. CTS becomes the transmitter

enable and

DCD becomes the receiver enable when this bit is set to ‘1’. However, the

Receiver Enable and Transmit Enable bits must be set before the

DCD and CTS pins can

be used in this manner. When the Auto Enables bit is set to ‘0’, the

DCD and CTS pins

are merely inputs to the corresponding status bits in Read Register 0. The state of

DCD is

ignored in the Local Loopback mode. The state of

CTS is ignored in both Auto Echo and

Local Loopback modes. If CTS disables the transmitter during a byte transmission, the

SCC will still complete the byte transfer.

Bit 4: Enter Hunt Mode

This command forces the comparison of sync characters or flags for the purpose of syn-

chronization. After reset, the SCC automatically enters the Hunt mode (except asynchro-

nous). Whenever a flag or sync character is matched, the Sync/Hunt bit in Read Register

0 is reset and, if External/Status Interrupt Enable is set, an interrupt sequence is initiated.

The SCC automatically enters the Hunt mode when an abort condition is received or

when the receiver is disabled.

Bit 3: Receiver CRC Enable

This bit is used to initiate CRC calculation at the beginning of the last byte transferred

from the Receiver Shift register to the receive FIFO. This operation occurs independently

of the number of bytes in the receive FIFO. When a particular byte is to be excluded from

CRC calculation, this bit should be reset before the next byte is transferred to the receive

FIFO. If this feature is used, care must be taken to ensure that eight bits per character is

selected in the receiver because of an inherent delay from the Receive Shift register to

the CRC checker.

This bit is internally set to ‘1’ in SDLC mode and the SCC calculates CRC on all bits ex-

cept inserted zeros between the opening and closing character flags. This bit is ignored in

asynchronous modes.

AM8530 Datasheet(PDF) 120 Page - Advanced Micro Devices

AM8530 Datasheet(HTML) 120 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL