CS5530A datasheet(167/259 Pages) AMD

167 / 259 page

AMD Geode™ CS5530A Companion Device Data Book

167

Revision 1.1

GPIO1 SMI Status (Read Only): SMI was caused by transition on (properly-configured) GPIO1 pin? 0 = No; 1 = Yes.

This is the second level of SMI status reporting. The top level is reported at F1BAR+Memory Offset 00h/02h[0].

SMI generation enabling is at F0 Index 92h[1].

GPIO0 SMI Status (Read Only): SMI was caused by transition on (properly-configured) GPIO0 pin? 0 = No; 1 = Yes.

This is the second level of SMI status reporting. The top level is reported at F1BAR+Memory Offset 00h/02h[0].

SMI generation enabling is at F0 Index 92h[0].

Lid Position (Read Only): This bit maintains the current status of the lid position. If the GPIO6 pin is configured as the lid

switch indicator, this bit reflects the state of the pin.

Lid Switch SMI Status (Read Only): SMI was caused by a transition on the GPIO6 (lid switch) pin? 0 = No; 1 = Yes.

For this to happen, the GPIO6 pin must be configured both as an input (F0 Index 90h[6] = 0) and as the lid switch

(F0 Index 92h[6] =1).

Codec SDATA_IN SMI Status (Read Only): SMI was caused by AC97 codec producing a positive edge on SDATA_IN?

0 = No; 1 = Yes.

This is the second level of status is reporting. The top level status is reported at F1BAR+Memory Offset 00h/02h[0].

SMI generation enabling is at F0 Index 80h[5].

RTC Alarm (IRQ8) SMI Status (Read Only): SMI was caused by an RTC interrupt? 0 = No; 1 = Yes.

This SMI event can only occur while in 3V Suspend and an RTC interrupt occurs.

This is the second level of SMI status reporting. The top level is reported at F1BAR+Memory Offset 00h/02h[0].

ACPI Timer SMI Status (Read Only): SMI was caused by an ACPI Timer MSB toggle? 0 = No; 1 = Yes.

This is the second level of SMI status reporting. The top level is reported at F1BAR+Memory Offset 00h/02h[0].

SMI generation configuration is at F0 Index 83h[5].

Note: Properly-configured means that the GPIO pin must be enabled as a GPIO (if multiplexed pin), an input, and to cause an SMI.

This register provides status on several miscellaneous power management events that generate SMIs, as well as the status of

the Lid Switch. It is called a Mirror register since an identical register exists at F0 Index F7h. Reading this register does not clear

the status, while reading its counterpart at F0 Index F7h does clear the status.

Index 88h

General Purpose Timer 1 Count Register (R/W)

Reset Value = 00h

7:0

General Purpose Timer 1 Count: This register holds the load value for GP Timer 1. This value can represent either an 8-

bit or 16-bit timer (selected at F0 Index 8Bh[4]). It is loaded into the timer when the timer is enabled (F0 Index 83h[0] =1).

Once enabled, an enabled event (configured in F0 Index 89h[6:0]) reloads the timer.

The timer is decremented with each clock of the configured timebase. Upon expiration of the timer, an SMI is generated and

the top level SMI status is reported at F1BAR+Memory Offset 00h/02h[9]. The second level SMI status is reported at

F1BAR+Memory Offset 04h/06h[0]).

Once expired, this timer must be re-initialized by either disabling and enabling it, or writing a new count value here.

This timer’s timebase can be configured as 1 msec or 1 sec at F0 Index 89h[7].

Index 89h

General Purpose Timer 1 Control Register (R/W)

Reset Value = 00h

Timebase for General Purpose Timer 1: Selects timebase for GP Timer 1 (F0 Index 88h). 0 = 1 sec; 1 = 1 msec.

Re-trigger General Purpose Timer 1 on User Defined Device 3 (UDEF3) Activity: 0 = Disable; 1 = Enable.

Any access to the configured (memory or I/O) address range for UDEF3 reloads GP Timer 1. UDEF3 address

programming is at F0 Index C8h (base address register) and CEh (control register).

Re-trigger General Purpose Timer 1 on User Defined Device 2 (UDEF2) Activity: 0 = Disable; 1 = Enable.

Any access to the configured (memory or I/O) address range for UDEF2 reloads GP Timer 1. UDEF2 address

programming is at F0 Index C4h (base address register) and CDh (control register).

Re-trigger General Purpose Timer 1 on User Defined Device 1 (UDEF1) Activity: 0 = Disable; 1 = Enable.

Any access to the configured (memory or I/O) address range for UDEF1 reloads GP Timer 1. UDEF1 address

programming is at F0 Index C0h (base address register) and CCh (control register)

Re-trigger General Purpose Timer 1 on Keyboard or Mouse Activity: 0 = Disable; 1 = Enable

Any access to the keyboard or mouse I/O address range (listed below) reloads GP Timer 1.

Keyboard Controller: I/O Ports 060h/064h

COM1: I/O Port 3F8h-3FFh (if F0 Index 93h[1:0] = 10 this range is included)

COM2: I/O Port 2F8h-2FFh (if F0 Index 93h[1:0] = 11 this range is included)

Table 5-15. F0 Index xxh: PCI Header and Bridge Configuration Registers (Continued)

Bit

Description

CS5530A Datasheet(PDF) 167 Page - Advanced Micro Devices

CS5530A Datasheet(HTML) 167 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL