LAN9250 datasheet(123/421 Pages) MICROCHIP

123 / 421 page

 2015 Microchip Technology Inc.

DS00001913A-page 123

LAN9250

Note 2:

The bit width format is: command bit width, address / dummy bit width, data bit width.

10.2.1

DEVICE INITIALIZATION

Until the device has been initialized to the point where the various configuration inputs are valid, the SPI/SQI interface

does not respond to and is not affected by any external pin activity.

Once device initialization completes, the SPI/SQI interface will ignore the pins until a rising edge of SCS# is detected.

10.2.1.1

SPI/SQI Slave Read Polling for Initialization Complete

Before device initialization, the SPI/SQI interface will not return valid data. To determine when the SPI/SQI interface is

functional, the Byte Order Test Register (BYTE_TEST) should be polled. Once the correct pattern is read, the interface

can be considered functional. At this point, the Device Ready (READY) bit in the Hardware Configuration Register

(HW_CFG) can be polled to determine when the device is fully configured.

10.2.2

ACCESS DURING AND FOLLOWING POWER MANAGEMENT

During any power management mode other than D0, reads and writes are ignored and the SPI/SQI interface does not

respond to and is not affected by any external pin activity.

Once the power management mode changes back to D0, the SPI/SQI interface will ignore the pins until a rising edge

of SCS# is detected.

To determine when the SPI/SQI interface is functional, the Byte Order Test Register (BYTE_TEST) should be polled.

Once the correct pattern is read, the interface can be considered functional. At this point, the Device Ready (READY)

bit in the Hardware Configuration Register (HW_CFG) can be polled to determine when the device is fully configured.

10.2.3

SPI CONFIGURATION COMMANDS

10.2.3.1

Enable SQI

The Enable SQI instruction changes the mode of operation to SQI. This instruction is supported in SPI bus protocol only

with clock frequencies up to 80 MHz. This instruction is not supported in SQI bus protocol.

The SPI slave interface is selected by first bringing SCS# active. The 8-bit EQIO instruction, 38h, is input into the SI/

SIO[0] pin one bit per clock. The SCS# input is brought inactive to conclude the cycle.

TABLE 10-2:

SQI INSTRUCTIONS

Instruction

Description

Bit width

Note 2

Inst.

code

Addr.

Bytes

Dummy

Bytes

Data

bytes

Max

Freq.

Configuration

RSTQIO

Reset SQI

4-0-0

FFh

80 MHz

Read

FASTREAD

Read at higher

speed

4-4-4

0Bh

4 to



80 MHz

Write

WRITE

Write

4-4-4

02h

4 to



80 MHz

Note:

The Host should only use single register reads (one data cycle per SCS# low) while polling the BYTE_TEST

Note:

The Host should only use single register reads (one data cycle per SCS# low) while polling the BYTE_TEST

LAN9250 Datasheet(PDF) 123 Page - Microchip Technology

LAN9250 Datasheet(HTML) 123 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL