| Electronic Components Datasheet Search |
|
LAN8700 Datasheet(PDF) 39 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
LAN8700 Datasheet(HTML) 39 Page - Microchip Technology |
|
39 / 74 page ![]() 2007-2016 Microchip Technology Inc. DS00002260A-page 39 LAN8700/LAN8700i TABLE 5-40: REGISTER 26 - SYMBOL ERROR COUNTER Address Name Description Mode Default 26.15:0 Sym_Err_Cnt 100Base-TX receiver-based error register that increments when an invalid code symbol is received including IDLE symbols. The counter is incremented only once per packet, even when the received packet contains more than one symbol error. The 16-bit register counts up to 65,536 (216) and rolls over to 0 if incremented beyond that value. This register is cleared on reset, but is not cleared by reading the register. It does not increment in 10Base-T mode. RO 0 TABLE 5-41: REGISTER 27 - SPECIAL CONTROL/STATUS INDICATIONS Address Name Description Mode Default 27.15 AMDIXCTRL HP Auto-MDIX control 0 - Auto-MDIX enable 1 - Auto-MDIX disabled (use 27.13 to control channel) RW 0 27.14 Reserved Reserved RW 0 27.13 CH_SELECT Manual Channel Select 0 - MDI -TX transmits RX receives 1 - MDIX -TX receives RX transmits RW 0 27.12 Reserved Write as 0. Ignore on read. RW 0 27:11 SQEOFF Disable the SQE (Signal Quality Error) test (Heartbeat): 0 - SQE test is enabled. 1 - SQE test is disabled. RW, NASR 0 27.10:5 Reserved Write as 0. Ignore on read. RW 000000 27.4 XPOL Polarity state of the 10Base-T: 0 - Normal polarity 1 - Reversed polarity RO 0 27.3:0 Reserved Reserved RO XXXXb TABLE 5-42: REGISTER 28 - SPECIAL INTERNAL TESTABILITY CONTROLS Address Name Description Mode Default 28.15:0 Reserved Do not write to this register. Ignore on read. RW N/A TABLE 5-43: REGISTER 29 - INTERRUPT SOURCE FLAGS Address Name Description Mode Default 29.15:8 Reserved Ignore on read. RO/ LH 0 29.7 INT7 1 = ENERGYON generated 0 = not source of interrupt RO/ LH X 29.6 INT6 1 = Auto-Negotiation complete 0 = not source of interrupt RO/ LH X 29.5 INT5 1 = Remote Fault Detected 0 = not source of interrupt RO/ LH X 29.4 INT4 1 = Link Down (link status negated) 0 = not source of interrupt RO/ LH X 29.3 INT3 1 = Auto-Negotiation LP Acknowledge 0 = not source of interrupt RO/ LH X 29.2 INT2 1 = Parallel Detection Fault 0 = not source of interrupt RO/ LH X |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |