Electronic Components Datasheet Search
  English  ▼

X  

ADXL366 Datasheet(PDF) 18 Page - Analog Devices

Part # ADXL366
Description  Micropower, 3-Axis, ±2g/±4g/±8g Digital Output MEMS Accelerometer
PDF  71 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

ADXL366 Datasheet(HTML) 18 Page - Analog Devices

Back Button ADXL366 Datasheet HTML 14Page - Analog Devices ADXL366 Datasheet HTML 15Page - Analog Devices ADXL366 Datasheet HTML 16Page - Analog Devices ADXL366 Datasheet HTML 17Page - Analog Devices ADXL366 Datasheet HTML 18Page - Analog Devices ADXL366 Datasheet HTML 19Page - Analog Devices ADXL366 Datasheet HTML 20Page - Analog Devices ADXL366 Datasheet HTML 21Page - Analog Devices ADXL366 Datasheet HTML 22Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 18 / 71 page
background image
Data Sheet
ADXL366
THEORY OF OPERATION
analog.com
Rev. 0 | 18 of 71
The ADXL366 is a complete 3-axis acceleration measurement
system that operates at extremely low power consumption levels.
The ADXL366 measures both dynamic acceleration, resulting from
motion or shock, and static acceleration, such as tilt. Acceleration
is reported digitally, and the device communicates via either the
SPI or the I2C protocol. Built-in digital logic enables autonomous
operation and implements functionality that enhances system level
power savings.
MECHANICAL DEVICE OPERATION
The moving component of the sensor is a polysilicon surface-micro-
machined structure that is built on top of a silicon wafer. Polysilicon
springs suspend the structure over the surface of the wafer and
provide a resistance against acceleration forces.
Deflection of the structure is measured using differential capacitors
that consist of independent fixed plates and plates attached to the
moving mass. Acceleration deflects the structure and unbalances
the differential capacitor, resulting in a sensor output whose ampli-
tude is proportional to acceleration. Phase sensitive demodulation
determines the magnitude and polarity of the acceleration.
OPERATING MODES
The ADXL366 has the following three operating modes:
►
Measurement mode for continuous, wide bandwidth sensing
►
Wake-up mode for limited bandwidth activity detection
►
Standby mode for power conservation
Measurement Mode
Measurement mode is the normal operating mode of the ADXL366.
In this mode, acceleration data is read continuously, and the
accelerometer consumes less than 1.3µA across its entire range
of output data rates of up to 400Hz (normal mode at 25°C). All
features described in this data sheet are available when operating
the ADXL366 in this mode.
The ADXL366 is a true ultra-low power accelerometer because
its supply current is 0.96µA at 100Hz ODR. Other accelerometers
derive low current by using a specific low power mode that power
cycles acceleration sensing. The resulting undersampling can lead
to aliasing of the input acceleration. The ADXL366 does not under-
sample the input signal at any of its output data rates when in
measurement mode.
Note that after entering measurement mode, a 100ms wait time
must be observed before reading acceleration data to allow the
output time to settle after entering measurement mode.
Wake-Up Mode
Wake-up mode reduces current consumption to a low level by
sampling the input periodically and turning the accelerometer elec-
tronics off between measurements. This mode is often used to
distinguish between the presence and absence of motion, but it can
also be used as a live data stream.
The ADXL366 offers four user-selectable wake-up rates ranging
from approximately 12.5SPS to approximately 1.5SPS. In wake-up
mode, acceleration is measured at regular intervals. Between sam-
ples, the accelerometer electronics are in a lower power state (see
Figure 41).
Figure 41. Acceleration Sampling
Wake-up mode is ideal for implementation of a motion-activated
on or off switch. For many systems, a few measurements per
second are sufficient to detect movements that can wake up the
system. After the system is awake, it can switch into a higher
data-rate mode for more precise motion measurements. Note that
the time duration for the first wake-up is longer than the subsequent
wake-ups.
In wake-up mode, if motion is detected, the accelerometer can
respond in any of the following ways:
►
Remain in wake-up mode and continue to sample data, when
activity interrupt is not triggered
►
Switch into full bandwidth measurement mode, when activity
interrupt is triggered
►
Signal an interrupt to a microcontroller
►
Wake-up downstream circuitry, depending on the configuration
The response of the accelerometer is configurable via register
settings. Note that the time duration for the first wake-up data point
is up to 10ms slower than the subsequent data points. Wake-up
mode is not supported in low noise mode and ultra-low noise mode.
Standby Mode
Placing the ADXL366 in standby mode suspends measurement and
reduces current consumption to 47nA (typical). Pending interrupts
and data are preserved, and no new interrupts are generated.
The ADXL366 powers up in standby mode with all sensor functions
turned off. Note that any changes to the registers before the
POWER_CTL register (Register 0x00 to Register 0x2D) must be
made with the device in standby mode. If changes are made while
the ADXL366 is in measurement mode, these changes may be
effective for only part of a measurement. Ensure that the change of
the data capture configuration only occurs in standby mode.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com