Electronic Components Datasheet Search
  English  ▼

X  

ADSP-SC583 Datasheet(PDF) 9 Page - Analog Devices

Part # ADSP-SC583
Description  SHARC Dual-Core DSP with Arm Cortex-A5
PDF  173 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

ADSP-SC583 Datasheet(HTML) 9 Page - Analog Devices

Back Button ADSP-SC583 Datasheet HTML 5Page - Analog Devices ADSP-SC583 Datasheet HTML 6Page - Analog Devices ADSP-SC583 Datasheet HTML 7Page - Analog Devices ADSP-SC583 Datasheet HTML 8Page - Analog Devices ADSP-SC583 Datasheet HTML 9Page - Analog Devices ADSP-SC583 Datasheet HTML 10Page - Analog Devices ADSP-SC583 Datasheet HTML 11Page - Analog Devices ADSP-SC583 Datasheet HTML 12Page - Analog Devices ADSP-SC583 Datasheet HTML 13Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 173 page
background image
Rev. B
|
Page 9 of 173
|
December 2018
ADSP-SC582/SC583/SC584/SC587/SC589/ADSP-21583/21584/21587
The processing elements are referred to as PEx and PEy data
registers and each contain an arithmetic logic unit (ALU), mul-
tiplier, shifter, and register file. PEx is always active and PEy is
enabled by setting the PEYEN mode bit in the mode control
register (MODE1).
Single instruction multiple data (SIMD) mode allows the pro-
cessors to execute the same instruction in both processing
elements, but each processing element operates on different
data. This architecture efficiently executes math intensive DSP
algorithms. In addition to all the features of previous generation
SHARC cores, the SHARC+ core also provides a new and sim-
pler way to execute an instruction only on the PEy data register.
SIMD mode also affects the way data transfers between memory
and processing elements because to sustain computational
operation in the processing elements requires twice the data
bandwidth. Therefore, entering SIMD mode doubles the band-
width between memory and the processing elements. When
using the DAGs to transfer data in SIMD mode, two data values
transfer with each memory or register file access.
Independent, Parallel Computation Units
Within each processing element is a set of pipelined computa-
tional units. The computational units consist of a multiplier,
arithmetic/logic unit (ALU), and shifter. These units are
arranged in parallel, maximizing computational throughput.
These computational units support IEEE 32-bit single-precision
floating-point, 40-bit extended-precision floating-point, IEEE
64-bit double-precision floating-point, and 32-bit fixed-point
data formats.
A multifunction instruction set supports parallel execution of
ALU and multiplier operations. In SIMD mode, the parallel
ALU and multiplier operations occur in both processing ele-
ments per core.
All processing operations take one cycle to complete. For all
floating-point operations, the processor takes two cycles to
complete in case of data dependency. Double-precision float-
ing-point data take two to six cycles to complete. The processor
stalls for the appropriate number of cycles for an interlocked
pipeline plus data dependency check.
Core Timer
Each SHARC+ processor core also has a timer. This extra timer
is clocked by the internal processor clock and is typically used as
a system tick clock for generating periodic operating system
interrupts.
Data Register File
Each processing element contains a general-purpose data regis-
ter file. The register files transfer data between the computation
units and the data buses, and store intermediate results. These
10-port, 32-register register files (16 primary, 16 secondary),
combined with the enhanced Harvard architecture of the pro-
cessor, allow unconstrained data flow between computation
units and internal memory. The registers in the PEx data regis-
ter file are referred to as R0–R15 and in the PEy data register file
as S0–S15.
Context Switch
Many of the registers of the processor have secondary registers
that can activate during interrupt servicing for a fast context
switch. The data, DAG, and multiplier result registers have sec-
ondary registers. The primary registers are active at reset, while
control bits in MODE1 activate the secondary registers.
Universal Registers (USTAT)
General-purpose tasks use the universal registers. The four
USTAT registers allow easy bit manipulations (set, clear, toggle,
test, XOR) for all control and status peripheral registers.
The data bus exchange register (PX) permits data to pass
between the 64-bit PM data bus and the 64-bit DM data bus or
between the 40-bit register file and the PM or DM data bus.
These registers contain hardware to handle the data width
difference.
Data Address Generators With Zero-Overhead Hardware
Circular Buffer Support
For indirect addressing and implementing circular data buffers
in hardware, the ADSP-SC58x/ADSP-2158x processor uses the
two data address generators (DAGs). Circular buffers allow effi-
cient programming of delay lines and other data structures
required in digital signal processing, and are commonly used in
digital filters and Fourier transforms. The two DAGs of the pro-
cessors contain sufficient registers to allow the creation of up to
32 circular buffers (16 primary register sets and 16 secondary
sets). The DAGs automatically handle address pointer wrap-
around, reduce overhead, increase performance, and simplify
implementation. Circular buffers can start and end at any mem-
ory location.
Flexible Instruction Set Architecture (ISA)
The ISA, a 48-bit instruction word, accommodates various par-
allel operations for concise programming. For example, the
processors can conditionally execute a multiply, an add, and a
subtract in both processing elements while branching and fetch-
ing up to four 32-bit values from memory—all in a single
instruction. Additionally, the double-precision floating-point
instruction set is an addition to the SHARC+ core.
Variable Instruction Set Architecture (VISA)
In addition to supporting the standard 48-bit instructions from
previous SHARC processors, the SHARC+ core processors sup-
port 16-bit and 32-bit opcodes for many instructions, formerly
48-bit in the ISA. This feature, called variable instruction set
architecture (VISA), drops redundant or unused bits within the
48-bit instruction to create more efficient and compact code.
The program sequencer supports fetching these 16-bit and 32-
bit instructions from both internal and external memories.
VISA is not an operating mode; it is only address dependent
(refer to memory map ISA/VISA address spaces in Table 7).
Furthermore, it allows jumps between ISA and VISA instruc-
tion fetches.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com