LP3910 datasheet(64/72 Pages) TI1

64 / 72 page

1.0

2.0

3.0

4.0

5.0

DC BIAS (V)

100%

80%

60%

40%

20%

0402, 6.3V, X5R

0603, 10V, X5M

LP3910

SNVS481M – NOVEMBER 2006 – REVISED DECEMBER 2015

www.ti.com

In particular, the output capacitor selection must take account of all the capacitor parameters, to ensure that the

specification is met within the application. The capacitance can vary with DC bias conditions as well as

temperature and frequency of operation. Capacitor values also show some decrease over time due to aging. The

capacitor parameters are also dependent on the particular case size, with smaller sizes giving poorer

performance figures in general. As an example, Figure 76 shows a typical graph comparing different capacitor

case sizes.

Figure 76. Typical Variation in Capacitance vs DC Bias

As shown in Figure 76, increasing the DC Bias condition can result in the capacitance value that falls below the

minimum value given in the recommended capacitor specifications table. Note that Figure 76 shows the

capacitance out of spec for the 0402 case size capacitor at higher bias voltages. It is therefore recommended

that the capacitor manufacturers’ specifications for the nominal value capacitor are consulted for all conditions,

as some capacitor sizes (for example, 0402) may not be suitable in the actual application.

Capacitance of a ceramic capacitor can vary with temperature. The capacitor type X7R, which operates over a

temperature range of

−55°C to +125°C, only varies the capacitance to within ±15%. The capacitor type X5R has

a similar tolerance over a reduced temperature range of

−55°C to +85°C. Many large value ceramic capacitors,

larger than 1

μF are manufactured with Z5U or Y5V temperature characteristics. Their capacitance can drop by

more than 50% as the temperature varies from 25°C to 85°C. Therefore X7R is recommended over Z5U and

Y5V in applications where the ambient temperature changes significantly above or below 25°C.

Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more

expensive when comparing equivalent capacitance and voltage ratings in the 0.47-

μF to 4.7-μF range.

Another important consideration is that tantalum capacitors have higher ESR values than equivalent size

ceramics. This means that while it may be possible to find a tantalum capacitor with an ESR value within the

stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic

capacitor with the same ESR value. The ESR of a typical tantalum increases about 2:1 as the temperature goes

from +25°C down to

−40°C, so some guard band must be allowed.

9.2.2.2.1.4

Noise Bypass Capacitors for VREFH Pin

Connecting respectively 100 nF and 1 nF grounded bypass capacitors to the VREFH pin significantly reduces

noise on the LDO outputs. VREFH is a high-impedance node connected to a bandgap reference used for the

LDOs. Any significant loading on this node causes a change on the regulated output voltages. For this reason,

DC leakage current through these pins must be kept as low as possible for best output voltage accuracy. The

types of capacitors best suited for the noise bypass capacitors are ceramic and film capacitors. High-quality

ceramic capacitors with either NPI or COG dielectric typically have very low leakage. Polypropylene and

polycarbonate film capacitors are available in small surface-mount packages and typically have extremely low

leakage current. Residual solder flux is another potential source of leakage, which mandates thorough cleaning

of the assembled PCBs.

Submit Documentation Feedback

Product Folder Links: LP3910

LP3910 Datasheet(PDF) 64 Page - Texas Instruments

LP3910 Datasheet(HTML) 64 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

Datasheet Download

Link URL