S70FS01GS datasheet(20/141 Pages) CYPRESS

20 / 141 page

S70FS01GS

Document Number: 002-03833 Rev. *C

Page 20 of 141

3.3.8

Single Input Cycle - Host to Memory Transfer

Several commands transfer information after the instruction on the single serial input (SI) signal from host to the memory device. The

host keeps RESET# high, CS# low, and drives SI as needed for the command. The memory does not drive the Serial Output (SO)

signal.

The expected next interface state depends on the instruction. Some instructions continue sending address or data to the memory

using additional Single Input Cycles. Others may transition to Single Latency, or directly to Single, Dual, or Quad Output cycle

states.

3.3.9

Single Latency (Dummy) Cycle

Read commands may have zero to several latency cycles during which read data is read from the main Flash memory array before

transfer to the host. The number of latency cycles are determined by the Latency Code in the configuration register (CR2V[3:0]).

During the latency cycles, the host keeps RESET# high, CS# low. The Write Protect (WP#) signal is ignored. The host may drive the

SI signal during these cycles or the host may leave SI floating. The memory does not use any data driven on SI / I/O0 or other I/O

signals during the latency cycles. The memory does not drive the Serial Output (SO) or I/O signals during the latency cycles.

The next interface state depends on the command structure i.e. the number of latency cycles, and whether the read is single, dual,

or quad width.

3.3.10

Single Output Cycle - Memory to Host Transfer

Several commands transfer information back to the host on the single Serial Output (SO) signal. The host keeps RESET# high, CS#

low. The Write Protect (WP#) signal is ignored. The memory ignores the Serial Input (SI) signal. The memory drives SO with data.

The next interface state continues to be Single Output Cycle until the host returns CS# to high ending the command.

3.3.11

Dual Input Cycle - Host to Memory Transfer

The Read Dual I/O command transfers two address or mode bits to the memory in each cycle. The host keeps RESET# high, CS#

low. The Write Protect (WP#) signal is ignored. The host drives address on SI / IO0 and SO / IO1.

The next interface state following the delivery of address and mode bits is a Dual Latency Cycle if there are latency cycles needed or

Dual Output Cycle if no latency is required.

3.3.12

Dual Latency (Dummy) Cycle

Read commands may have zero to several latency cycles during which read data is read from the main Flash memory array before

transfer to the host. The number of latency cycles are determined by the Latency Code in the configuration register (CR2V[3:0]).

During the latency cycles, the host keeps RESET# high, CS# low. The Write Protect (WP#) signal is ignored. The host may drive the

SI / IO0 and SO / IO1 signals during these cycles or the host may leave SI / IO0 and SO / IO1 floating. The memory does not use

any data driven on SI / IO0 and SO / IO1 during the latency cycles. The host must stop driving SI / IO0 and SO / IO1 on the falling

edge at the end of the last latency cycle. It is recommended that the host stop driving them during all latency cycles so that there is

sufficient time for the host drivers to turn off before the memory begins to drive at the end of the latency cycles. This prevents driver

conflict between host and memory when the signal direction changes. The memory does not drive the SI / IO0 and SO / IO1 signals

during the latency cycles.

The next interface state following the last latency cycle is a Dual Output Cycle.

3.3.13

Dual Output Cycle - Memory to Host Transfer

The Read Dual Output and Read Dual I/O return data to the host two bits in each cycle. The host keeps RESET# high, CS# low. The

Write Protect (WP#) signal is ignored. The memory drives data on the SI / IO0 and SO / IO1 signals during the dual output cycles.

The next interface state continues to be Dual Output Cycle until the host returns CS# to high ending the command.

S70FS01GS Datasheet(PDF) 20 Page - Cypress Semiconductor

S70FS01GS Datasheet(HTML) 20 Page - Cypress Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL